![cisco easy vpn cisco easy vpn](https://img2.docer.pl/image/l/e0vc0ex.png)
Not required for the Easy VPN Client inside interface or the inside hosts.Įxtension Mode (NEM) makes the inside interface and all inside hosts route-ableĪcross the enterprise network over the tunnel. Remote are hidden, and cannot be accessed directly. The network and addresses on the private side of the Easy VPN VPN Remote performs Port Address Translation (PAT) for all VPN traffic for its Whether the hosts behind the Easy VPN Remote are accessible or not from theĪlso called Port Address Translation (PAT) mode, isolates all devices on theĮasy VPN Remote private network from those on the enterprise network. Trustpoint command to identify a pre-configured trustpoint.
![cisco easy vpn cisco easy vpn](https://image.slidesharecdn.com/easyvpn-121113020934-phpapp01/95/easy-vpn-9-638.jpg)
Vpngroup command to configure its name and pre-shared key, or the On the ASAs configured as primary or secondary Easy VPN Servers.Įasy VPN Remote client specifies the group policy using the To change certain attributes, you must modify them Pushes group policy or user attributes to the Easy VPN Remote hardware clientĭetermining tunnel behavior. The Easy VPN Server, that will be used for the connection. If your environment allows UDP, however, configuring IPsec overĮstablishment, the Easy VPN Remote specifies the tunnel group, configured on Ipsec-over-tcp command to configure this. Within TCP packets to enable secure tunneling. Protocol (ESP, Protocol 50) or Internet Key Exchange (IKE, UDP 500) in suchĮnvironments, you must configure the client and the server to encapsulate IPsec Some environments, such as those with certain firewall rules, or VPN hardware client and server encapsulate IPsec in User Datagram Protocol Time, the client will proceed to set up the tunnel to the second secondary VPN If the setup tunnel to theįirst secondary server fails, and the primary server comes online during this Tries the connection to the first secondary VPN server, and then sequentiallyĭown the list of VPN servers at 8 second intervals. If unable to set up the tunnel to the primary server, the client Server command in global configuration mode to configure these Remote configures the IP address of the primary Easy VPN Server and optionally, Secondary servers, their configuration must be identical to the primary server. The Easy VPN Remote hardware client's configuration must beĬompatible with the VPN configuration on the Easy VPN Server headend. AAA rules are added on the BVI interface alone. The internal secure interface, the following applies:Īll BVI member interfaces are considered Internal Secured interfaces irrespective of their own security levels.ĪCL and NAT rules need to be added on all the member interfaces.
![cisco easy vpn cisco easy vpn](https://www.cisco.com/c/dam/en/us/products/collateral/security/ios-easy-vpn/data_sheet_c78-457320.doc/_jcr_content/renditions/data_sheet_c78-457320-2.jpg)
When a virtual interface (a Bridged Virtual Interface or BVI) is selected upon startup or assigned by the administrator as You cannot change the external interface from the automaticallyįor example, on an ASA5506 platform, the factory configuration has a BVI with the highest security level interface set toġ00 (with its member interfaces also at level 100), and an external interface with security level zero. You can change the internal secure interface using the vpnclient secure interface command if desired, to or from, a physical or virtual interface. That there are two or more interfaces with the same highest security level, Easy VPN is disabled. The physical or virtual interface with the highest security level is used for the internal connection to secure resources. With the lowest security level is used for the external connection to an Easy VPN server. Upon system startup, the Easy VPN external and internal interfaces are determined by their security level. The following sections describe Easy VPN options and settings. Host is on the inside network of the ASA. Use an external switch when using Easy VPN Remote with multiple AnĪSA cannot function as both an Easy VPN Remote and an Easy VPN Serverĥ506-X, 5506W-X, 5506H-X and 5508-X models support 元 switching not L2 TheĮasy VPN server can be another ASA (any model), or a Cisco IOS-based router.
![cisco easy vpn cisco easy vpn](https://s4.51cto.com/attachment/200901/200901171232136437859.jpg)
It implements the Cisco Unity Client protocol,Īllowing administrators to define most VPN parameters on the Easy VPN Server, simplifying the Easy VPN Remote configuration.įirePOWER models 5506-X, 5506W-X, 5506H-X, and 5508-X support Easy VPN RemoteĪs a hardware client that initiates the VPN tunnel to an Easy VPN Server. Cisco Easy VPN offersįlexibility, scalability, and ease of use for site-to-site and remote-access VPNs.
#Cisco easy vpn how to#
This chapter describes how to configure any ASA as an Easy VPN Server,Īnd the Cisco ASA with FirePOWER- 5506-X, 5506W-X, 5506H-X, and 5508-X modelsĬisco Ezvpn greatly simplifies configuration and deployment of VPN for remote offices and mobile workers.